ねんがんのJuniper EX4200-24Tをてにいれたぞ！
eBayで落札したEX4200がとどいたー！
とりあえず電源入れて、コンソールケーブル繋いで、ちゃんと動くね、というとこまでしかさわってませんが。
やっぱりファンの音大きいですね。甲高い音で、結構耳障りです。1Uサイズだから仕方ないんでしょうけど。そもそも人がいるところには置かないだろうし。
とりあえず、起動時のメッセージと初期コンフィグ載せておきますね。
U-Boot 1.1.6 (Feb 6 2008 - 11:27:42)
Board: EX4200-24T 2.17
EPLD: Version 6.0 (0x85)
DRAM: Initializing (1024 MB)
FLASH: 8 MB
USB: scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Consoles: U-Boot console
Found compatible API, ver. 7
FreeBSD/PowerPC U-Boot bootstrap loader, Revision 2.1
(marcelm@apg-bbuild01.juniper.net, Wed Feb 6 11:23:55 PST 2008)
Memory: 1024MB
Loading /boot/defaults/loader.conf
/kernel text=0x9af8c0 data=0x44a30+0x6ed74 syms=[0x4+0x88ca0+0x4+0x8f41e]
Hit [Enter] to boot immediately, or space bar for command prompt.
Booting [/kernel]...
Kernel entry at 0xa0000100 ...
GDB: no debug ports present
KDB: debugger backends: ddb
KDB: current backend: ddb
Copyright (c) 1996-2009, Juniper Networks, Inc.
All rights reserved.
Copyright (c) 1992-2006 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
JUNOS 9.2R3.5 #0: 2009-01-15 04:19:40 UTC
builder@amalath.juniper.net:/volume/build/junos/9.2/release/9.2R3.5/obj-powerpc/sys/compile/JUNIPER-EX
WARNING: debug.mpsafenet forced to 0 as ipsec requires Giant
Timecounter "decrementer" frequency 50000000 Hz quality 0
cpu0: Freescale e500v2 core revision 2.2
cpu0: HID0 80004080<EMCP,TBEN,EN_MAS7_UPDATE>
real memory = 1049624576 (1001 MB)
avail memory = 1027321856 (979 MB)
ETHERNET SOCKET BRIDGE initialising
nexus0: <PPC e500 Nexus device>
ocpbus0: <on-chip peripheral bus> on nexus0
openpic0: <OpenPIC in on-chip peripheral bus> iomem 0xfef40000-0xfef600b3 on ocpbus0
uart0: <16550 or compatible> iomem 0xfef04500-0xfef0450f irq 58 on ocpbus0
uart0: console (9600,n,8,1)
uart1: <16550 or compatible> iomem 0xfef04600-0xfef0460f irq 58 on ocpbus0
lbc0: <Freescale 8533 Local Bus Controller> iomem 0xfef05000-0xfef05fff,0xff000000-0xffffffff irq 22 on ocpbus0
cfi0: <AMD/Fujitsu - 8MB> iomem 0xff800000-0xffffffff on lbc0
syspld0 iomem 0xff000000-0xff00ffff on lbc0
tsec0: <eTSEC ethernet controller> iomem 0xfef24000-0xfef24fff irq 45,46,50 on ocpbus0
tsec0: hardware MAC address 00:26:88:6a:ee:3f
miibus0: <MII bus> on tsec0
e1000phy0: <Marvell 88E1112 Gigabit PHY> on miibus0
e1000phy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX-FDX, auto
pcib0: <Freescale MPC8544 PCI host controller> iomem 0xfef08000-0xfef08fff,0xf0000000-0xf3ffffff on ocpbus0
pci0: <PCI bus> on pcib0
pci0: <serial bus, USB> at device 18.0 (no driver attached)
ehci0: <Philips ISP156x USB 2.0 controller> mem 0xf0001000-0xf00010ff irq 22 at device 18.2 on pci0
usb0: EHCI version 1.0
usb0: <Philips ISP156x USB 2.0 controller> on ehci0
usb0: USB revision 2.0
uhub0: Philips EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
umass0: STMicroelectronics ST72682 High Speed Mode, rev 2.00/2.10, addr 2
pcib1: <Freescale MPC8544 PCI Express host controller> iomem 0xfef0a000-0xfef0afff,0xe0000000-0xe3ffffff,0xec000000-0xec0fffff on ocpbus0
pci1: <PCI bus> on pcib1
pcib2: <PCI-PCI bridge> at device 0.0 on pci1
pci2: <PCI bus> on pcib2
mpfe0: <Juniper EX-series Packet Forwarding Engine> mem 0xa4000000-0xa40fffff,0xa0000000-0xa3ffffff irq 19 at device 0.0 on pci2
pcib3: <Freescale MPC8544 PCI Express host controller> iomem 0xfef0b000-0xfef0bfff,0xe8000000-0xebffffff,0xec200000-0xec2fffff on ocpbus0
pci3: <PCI bus> on pcib3
pcib4: <PCI-PCI bridge> at device 0.0 on pci3
pci4: <PCI bus> on pcib4
mpfe1: <Juniper EX-series Packet Forwarding Engine> mem 0xb4000000-0xb40fffff,0xb0000000-0xb3ffffff irq 18 at device 0.0 on pci4
i2c0: <MPC85XX OnChip i2c controller> iomem 0xfef03000-0xfef03014 irq 59 on ocpbus0
i2c1: <MPC85XX OnChip i2c controller> iomem 0xfef03100-0xfef03114 irq 59 on ocpbus0
idma0: <mp85xxx DMA Controller> iomem 0xfef21000-0xfef21300 irq 36 on ocpbus0
bme0:Virtual BME driver initializing
Timecounters tick every 1.000 msec
Loading common multilink module.
IPsec: Initialized Security Association Processing.
da0 at umass-sim0 bus 0 target 0 lun 0
da0: <ST ST72682 2.10> Removable Direct Access SCSI-2 device
da0: 40.000MB/s transfers
da0: 1000MB (2048000 512 byte sectors: 64H 32S/T 1000C)
if_pfe_open: listener socket opened, listening on ...
Trying to mount root from ufs:/dev/da0s1a
Attaching /packages/jbase via /dev/mdctl...
Mounted jbase package on /dev/md0...
Mounted jcrypto-ex package on /dev/md1...
Mounted jdocs-ex package on /dev/md2...
Mounted jkernel-ex package on /dev/md3...
Mounted jpfe-ex42x package on /dev/md4...
Mounted jroute-ex package on /dev/md5...
Mounted jswitch-ex package on /dev/md6...
Mounted jweb-ex package on /dev/md7...
Executing /packages/mnt/jweb-ex-9.2R3.5/mount.post..
Automatic reboot in progress...
** Last Mounted on /instrootmnt
** Root file system
** Phase 1 - Check Blocks and Sizes
** Phase 2 - Check Pathnames
** Phase 3 - Check Connectivity
** Phase 4 - Check Reference Counts
** Phase 5 - Check Cyl groups
1243 files, 42403 used, 51858 free (50 frags, 6476 blocks, 0.1% fragmentation)
** Last Mounted on /config
** Phase 1 - Check Blocks and Sizes
** Phase 2 - Check Pathnames
** Phase 3 - Check Connectivity
** Phase 4 - Check Reference Counts
** Phase 5 - Check Cyl groups
5 files, 5 used, 28322 free (26 frags, 3537 blocks, 0.1% fragmentation)
** Last Mounted on /var
** Phase 1 - Check Blocks and Sizes
** Phase 2 - Check Pathnames
** Phase 3 - Check Connectivity
** Phase 4 - Check Reference Counts
** Phase 5 - Check Cyl groups
258 files, 341 used, 62458 free (82 frags, 7797 blocks, 0.1% fragmentation)
** Last Mounted on /var/tmp
** Phase 1 - Check Blocks and Sizes
** Phase 2 - Check Pathnames
** Phase 3 - Check Connectivity
** Phase 4 - Check Reference Counts
** Phase 5 - Check Cyl groups
2 files, 2 used, 160996 free (28 frags, 20121 blocks, 0.0% fragmentation)
Creating initial configuration...mgd: error: Cannot open configuration file: /config/juniper.conf
mgd: warning: activating factory configuration
mgd: commit complete
mgd: ----------------------------------------------------------
mgd: Please login as 'root'. No password is required.
mgd: To start Initial Setup, type 'ezsetup' at the JUNOS prompt.
mgd: To start JUNOS CLI, type 'cli' at the JUNOS prompt.
mgd: ----------------------------------------------------------
Setting initial options: debugger_on_panic=NO debugger_on_break=NO.
Starting optional daemons: .
Doing initial network setup:
.
Initial interface configuration:
additional daemons:.
savecore: could not be determined
savecore: no dumps found
Additional routing options: ipsec kld.
Doing additional network setup:.
Starting final network daemons:.
setting ldconfig path: /usr/lib /opt/lib
starting standard daemons: cron.
Local package initialization:.
starting local daemons:.
Thu Jan 15 06:56:14 UTC 2009
Amnesiac (ttyu0)
login: root
Password:
--- JUNOS 9.2R3.5 built 2009-01-15 04:19:40 UTC
root@% cli
root> show configuration
## Last commit: 2009-01-15 06:56:09 UTC by root
version 9.2R3.5;
system {
syslog {
user * {
any emergency;
}
file messages {
any notice;
authorization info;
}
file interactive-commands {
interactive-commands any;
}
}
commit {
factory-settings {
reset-chassis-lcd-menu;
reset-virtual-chassis-configuration;
}
}
## Warning: missing mandatory statement(s): 'root-authentication'
}
interfaces {
ge-0/0/0 {
unit 0 {
family ethernet-switching;
}
}
ge-0/0/1 {
unit 0 {
family ethernet-switching;
}
}
ge-0/0/2 {
unit 0 {
family ethernet-switching;
}
}
ge-0/0/3 {
unit 0 {
family ethernet-switching;
}
}
ge-0/0/4 {
unit 0 {
family ethernet-switching;
}
}
ge-0/0/5 {
unit 0 {
family ethernet-switching;
}
}
ge-0/0/6 {
unit 0 {
family ethernet-switching;
}
}
ge-0/0/7 {
unit 0 {
family ethernet-switching;
}
}
ge-0/0/8 {
unit 0 {
family ethernet-switching;
}
}
ge-0/0/9 {
unit 0 {
family ethernet-switching;
}
}
ge-0/0/10 {
unit 0 {
family ethernet-switching;
}
}
ge-0/0/11 {
unit 0 {
family ethernet-switching;
}
}
ge-0/0/12 {
unit 0 {
family ethernet-switching;
}
}
ge-0/0/13 {
unit 0 {
family ethernet-switching;
}
}
ge-0/0/14 {
unit 0 {
family ethernet-switching;
}
}
ge-0/0/15 {
unit 0 {
family ethernet-switching;
}
}
ge-0/0/16 {
unit 0 {
family ethernet-switching;
}
}
ge-0/0/17 {
unit 0 {
family ethernet-switching;
}
}
ge-0/0/18 {
unit 0 {
family ethernet-switching;
}
}
ge-0/0/19 {
unit 0 {
family ethernet-switching;
}
}
ge-0/0/20 {
unit 0 {
family ethernet-switching;
}
}
ge-0/0/21 {
unit 0 {
family ethernet-switching;
}
}
ge-0/0/22 {
unit 0 {
family ethernet-switching;
}
}
ge-0/0/23 {
unit 0 {
family ethernet-switching;
}
}
ge-0/1/0 {
unit 0 {
family ethernet-switching;
}
}
xe-0/1/0 {
unit 0 {
family ethernet-switching;
}
}
ge-0/1/1 {
unit 0 {
family ethernet-switching;
}
}
xe-0/1/1 {
unit 0 {
family ethernet-switching;
}
}
ge-0/1/2 {
unit 0 {
family ethernet-switching;
}
}
ge-0/1/3 {
unit 0 {
family ethernet-switching;
}
}
}
protocols {
igmp-snooping {
vlan all;
}
lldp {
interface all;
}
lldp-med {
interface all;
}
rstp;
}
poe {
interface all;
}
| 固定リンク
この記事へのコメントは終了しました。
コメント
おぉ。
ちなみに、おいくらだったんでしょうか?
投稿: tmizuno | 2010年2月12日 (金) 23時52分
$1800ぐらいでした。
まー、GbE x 24 (PoE x 8)のL3スイッチとしたら、そんなもんですかね？
そろそろおうちのスイッチをGbE対応にしたいってのもあって、つい…
Advanced Feature Licenseを入れないとIPv6しゃべってくれないっていうのと、（当然だけど）サポート全然ないのが弱点でしょうか。
投稿: きのし | 2010年2月12日 (金) 23時59分
ライセンス入れなくてもIPv6しゃべれますよ。 ただconfigをcommitするときにWarningが毎回出るのがうるさいだけです。
投稿: gap | 2010年9月 9日 (木) 13時37分